Author Topic: Oregon pine finish  (Read 1446 times)

Offline Juggy

  • Trade Count: (+30)
  • AVForums Veteran
  • *****
  • Posts: 3,905
  • Cape Town
Oregon pine finish
« on: June 21, 2016, 05:43:35 PM »
A friend of mine built this beautiful bar for me but I'm at a loss as to what to protect it with. I want a very natural finish but protection against water etc



Any advice?

Sent from my LG-H850 using Tapatalk

| Lounge System | Samsung UA55F8000 | Onkyo TX-RZ1100 | Tannoy XT 8F | Tannoy XT C | Intel NUC |
| Braai System | Samsung UA40J5300 | Sansui AU-222 | Intel NUC | Paradigm Mini Monitor V2 |

Online dekardy

  • Trade Count: (+14)
  • AVForums Veteran
  • ***
  • Posts: 262
Re: Oregon pine finish
« Reply #1 on: June 21, 2016, 06:20:02 PM »
Teak Oil natural, but your going to have to do it once a year.
Woodoc low gloss sealer

Offline Shonver

  • Trade Count: (+7)
  • AVForums Veteran
  • *****
  • Posts: 9,761
  • Criss-cross rhythms that explode with happiness
    • Elipse (under construction)
Re: Oregon pine finish
« Reply #2 on: June 21, 2016, 07:47:05 PM »
coasters! :teach:
________________

DON'T PANIC
Capie

Offline gapco

  • Trade Count: (0)
  • AVForums Veteran
  • ***
  • Posts: 227
Re: Oregon pine finish
« Reply #3 on: June 21, 2016, 11:07:40 PM »
Bourn Gleem interior is what I use on my oregon floors, doors etc... 
Give me an espresso and nobody gets hurt....

Offline oradba69

  • Commercial Member
  • Trade Count: (+5)
  • *****
  • Posts: 1,522
    • Lerange
Re: Oregon pine finish
« Reply #4 on: June 22, 2016, 05:15:35 AM »
Rubio monocoat.
Manufacturer of Audio Video furniture.
Importer and distributor of Trichord.
http://www.lerange.co.za

Offline Juggy

  • Trade Count: (+30)
  • AVForums Veteran
  • *****
  • Posts: 3,905
  • Cape Town
Re: Oregon pine finish
« Reply #5 on: June 28, 2016, 01:35:15 PM »
Would Wooddock number 20 be OK?
| Lounge System | Samsung UA55F8000 | Onkyo TX-RZ1100 | Tannoy XT 8F | Tannoy XT C | Intel NUC |
| Braai System | Samsung UA40J5300 | Sansui AU-222 | Intel NUC | Paradigm Mini Monitor V2 |

Offline tangmonster

  • Trade Count: (0)
  • AVForums Veteran
  • *****
  • Posts: 1,743
Re: Oregon pine finish
« Reply #6 on: June 29, 2016, 12:43:18 PM »
Would Wooddock number 20 be OK?

Our kitchen cabinets was built by someone who mostly does kitchens in oregon. Our countertop is yellow wood.

He suggested and swore by woodock 20 when I asked him what we should use for the counter top when the time comes to coat again.




Offline vleisman

  • Trade Count: (+6)
  • AVForums Veteran
  • *****
  • Posts: 1,199
Re: Oregon pine finish
« Reply #7 on: June 29, 2016, 12:59:58 PM »
I prefer the natural raw look for some things, not sure if that will work on the bar. Maybe also look at Rystix or Gripseal products if you like a matt finish. They're sealers as opposed to shiny varnish-type finishes.

Offline XL1000

  • Trade Count: (+66)
  • AVForums Veteran
  • *****
  • Posts: 1,239
Re: Oregon pine finish
« Reply #8 on: October 02, 2016, 07:04:15 PM »
Rubio monocoat.

I would listen to this man. Have you not see the finish he puts on his products! Damn fine.

Would Wooddock number 20 be OK?

No, go with the above.
Music is a moral law. It gives soul to the universe, wings to the mind, flight to the imagination, and charm and gaiety to life and to everything. Plato

Offline JimGore

  • Trade Count: (+3)
  • AVForums Veteran
  • *****
  • Posts: 4,409
Re: Oregon pine finish
« Reply #9 on: October 04, 2016, 08:48:44 AM »
Rubio monocoat.

Rubio monocoat is a very good product, but it's only available from one place (that I know of) and is very, very expensive.

I would apply a coat of sanding sealer, then knock that down with fine paper or steel wool, after which aply a coat or two of oil.

Kind regards,
Ian.

Online JonnyP

  • Trade Count: (+23)
  • AVForums Veteran
  • *****
  • Posts: 2,878
  • To the centre of the city in the night
Re: Oregon pine finish
« Reply #10 on: October 04, 2016, 09:52:57 PM »
On my hifi stand I used a natural finish, think it was woodoc 10 rather than 20, seals the wood but it looks natural.  3 coats with steel wool rub between.  Then oiled.
Are you waiting for loneliness to paralyse? Are you waiting for sister midnight to anaesthetise?

Offline oradba69

  • Commercial Member
  • Trade Count: (+5)
  • *****
  • Posts: 1,522
    • Lerange
Re: Oregon pine finish
« Reply #11 on: October 05, 2016, 06:34:11 AM »
Dont want to punt Rubio too much, but I get mine delivered to my door free and gratis.
They even sent a gentleman to demo it to me.
It is mind boggling to see how little of the stuff one uses and how easy it is to apply.
Manufacturer of Audio Video furniture.
Importer and distributor of Trichord.
http://www.lerange.co.za

Offline GerritV

  • Trade Count: (0)
  • AVForums Member
  • ***
  • Posts: 138
  • Who killed John Henry?
Re: Oregon pine finish
« Reply #12 on: October 19, 2016, 09:46:57 PM »
How would one apply the monocoat?  Any special techniques? What makes it so special and different vs. woodock no 10?

Offline Timber_MG

  • Trade Count: (+2)
  • AVForums Veteran
  • *****
  • Posts: 6,315
Re: Oregon pine finish
« Reply #13 on: October 20, 2016, 08:08:33 AM »
Dont want to punt Rubio too much, but I get mine delivered to my door free and gratis.
They even sent a gentleman to demo it to me.
It is mind boggling to see how little of the stuff one uses and how easy it is to apply.

It's over R2500/litre and available at MS Timbers and Silverton Houthandelaars.

Offline oradba69

  • Commercial Member
  • Trade Count: (+5)
  • *****
  • Posts: 1,522
    • Lerange
Re: Oregon pine finish
« Reply #14 on: October 20, 2016, 09:15:30 AM »
One uses very little Rubio monocoat. To give you an idea I use 12ml to finish one of my lecubes. (www.lecube.co.za).
Process is:
Finish wood to 150 180 or 220 depending on what the piece is.
Wipe the monocoat on with a scotchpad until it is nice and wet and dont absorb it any more.
Wipe the excess off with a cloth or the tissue paper they use at garages.
Leave for 24 hours to dry properly.
If you are in Gauteng call Yamkela on 0788891967 and ask him to come and demo it to you.
1.3l is about R1500 but you can buy smaller quantities as well.
Manufacturer of Audio Video furniture.
Importer and distributor of Trichord.
http://www.lerange.co.za